projectvasup.blogg.se

1. Retropie on debian software#
2. Retropie on debian code#
3. Retropie on debian trial#
4. Retropie on debian tv#
5. Retropie on debian download#

When you do see an image on your display, you will probably notice that it is at a very low resolution (640×480 to be precise). In other words the settings you have configured are the most basic to display and if they are not now showing on your display, then you should probably look at upgrading your device. When you enable safe mode you are basically telling RetroPie to render to it’s lowest possible settings. Boot up the Raspberry Pi to make sure that you now see the RetroPie loading screen and the subsequent menu screen. Now save the file, remove the micro SD card from your computer and insert it back into the Raspberry Pi. # uncomment if you get no picture on HDMI for a default "safe" mode

Retropie on debian code#

To do this, at around line 4 you will see the code below – The surest way to do this is to enable safe mode in the config.txt file. The first thing we need to do is to get RetroPie working on your display. The config.txt file is where you can amend many visual settings in RetroPie

Retropie on debian trial#

It is basically a trial and error process to determine which settings work best for your display.įirst off, lets gain access to the config.txt file by following the steps below. This may sound a bit intimidating at first but it is really very simple. Not all will be successful but hopefully at least one will be.Īll these solutions will lie in amending the settings within the config.txt file, which can be found in the route of your micro SD card. OK, there are a number of possible solutions to this issue. So, you have determined that it is your display that is causing the issue.

Retropie on debian tv#

Switching the display to a Dell computer monitor identified to me that it was my TV that was the issue as there were no problems running RetroPie when using the monitor. When my issue originally occurred the display I was using was a Sony Bravia KDL-32S2510 which was bought way back in 2005. If the issue occurred while using a normal TV it would be advisable to try using a computer monitor. Eliminating this possibility will allow you now to concentrate on other potential issues such as your display.įirstly, to determine whether or not it is your display that is causing the issue the best thing to do is to try your setup with another display.

Retropie on debian software#

If the problem still persists you can rest in the knowledge that it is not your software that is causing the issue. If the process was corrupted before it is likely that going through it again will fix the issue and you should be able to boot up RetroPie without any further issues.

Retropie on debian download#

Download RetroPie again from the RetroPie website and then Flash the image to your micro SD card. Either way, to make sure that none of these were at fault the best thing to do is repeat the processes you performed earlier. Perhaps the RetroPie files became corrupted when they were downloaded, or maybe the fault occurred when you burnt RetroPie onto the micro SD card. It is possible that the issue may have developed during software installation. The reason this issue is occuring is most likely down to your display and not your Raspberry Pi or RetroPie, however when troubleshooting it is important to eliminate the simple solutions first before getting your hands really dirty and delving into the backend code.

Here we will investigate this infuriating issue in more detail and explore a few possible solutions. Instead you are seeing a black screen because the display you are using doesn’t think there is anything to show.

To be more specific what is actually occurring is your display is not detecting the signal from the Raspberry Pi and therefore is not showing any image on the screen. Unfortunately finding a solution proved to be a little more troublesome than I expected, so I decided to write this article in case anyone else finds themselves in this unfortunate predicament.ĭepending on the display you are using to run RetroPie (and the fact that you’ve arrived at this page) it is entirely possible that you, like me, have encountered a blank screen when booting up. Sorry – but we no longer include images for Berryboot for the latest versions.Booting up RetroPie and being presented with a blank screen is an issue I have encountered on a number of occasions.